Préampli-Processeur CHORD DSP R VENDU TRÈS RARE! Préampli processeur exceptionnel en HC et, fait beaucoup plus rare. Chord dsp r preamp / surround controller, boxed. CHORD DSP R preamp/ surround controller. with dts and dolby 2 surround. Introduction The Chord DSP forms the centre of a High -End cinema and audio system. The DSP decodes Dolby Digital, DTS and DTS-ES and has the.
|Published (Last):||15 September 2004|
|PDF File Size:||11.72 Mb|
|ePub File Size:||8.87 Mb|
|Price:||Free* [*Free Regsitration Required]|
The trigger output is activated when a composite video input signal is detected SVideo The trigger output is activated when a SVideo input signal is detected VidSign The trigger output chrod activated when either a SVideo or composite video input signal is detected Vidsrc The trigger output is activated when any video source is selected Audiosrc The trigger output is activated when any audio source is selected Trigger 1 polarity This setting is used to determine the polarity of the trigger when it is activated.
This processing mode will copy the dsp8000r and right channels to the left and right surround channels.
chogd Use the front panel cursor left? These buttons are featured on the front panel and on the remote control. Wait until the autocalibration process is over. Digital input You can assign a digital input or you can turn off the digital input for the selected source.
Determine if a balanced audio input signal is used? TAPE This button is used to monitor the level and quality of your audio recording signal.
Used chord dsp for Sale |
If this LCD touch pad is pressed whilst not in the menus then the touch pad functions as an active input source search touch pad. Trigger 1 duration Duration determines the amount of time the trigger voltage is output for when activated. However the maximum difference between the nearest and the most distant speaker is 17 feet 5. This page features miscellaneous controls including those needed to use the music modes.
吏?? ?濡 GLV – Create arts through technology!
The audio can be delayed by up to ms up to a sample rate of 48kHz and 0 — 70ms at up to 96kHz in single millisecond steps. You can choose feet or meters. Three component video inputs and one output support HDTV-formats.
This menu chofd you to adjust the level of each of individual loudspeaker output.
DSP 8000 AV Processor
Pressing this button when DVD1 is selected will cycle the selection round to the end of the list at Ext 7. OUT Use this output to connect any display device such as a plasma screen or projector that has choed component video input. Allows direct measurement of speaker distances using the supplied microphone. Precautions must be taken to prevent accidental contact with power-line potentials.
Place the microphone on the listening position pointing towards the roof. This is to ensure that there will always be an audio signal present at the record outputs when using an analogue tape recorder. We hope you have many hours of enjoyment from this product. Size setup Used to define which speakers are present and whether they can handle low frequencies.
The trigger menu allows you to program the trigger outputs that will control other devices within your home theatre system. There are three main types of input and output connections on the DSP ; audio connections, video connections and control connections.
Allows direct level calibration using the supplied microphone. Bass Filter This allows you to chose the frequency point that the bass settings work from. Press this Fsp8000r touch pad to move downwards through the sub menus within the set up menu. This button functions as a toggle to mute and un -mute the outputs.
The interconnecting cables you use will depend on the available input and output sockets on your other equipment. This setting overrides the Treble setting in the Tone Setup. The distance each of your speakers are from the listening position are entered so that dspp8000r DSP can automatically adjust delays of signals to speakers to compensate for different configurations.
chlrd Steps 1, 2 and 3 gradually move the sound forward, and steps —1, -2 and —3 move the sound towards the surrounds. See the tape monitor section of this manual for more information.