The BSSMAP protocol was extended to be able to negotiate per-call IP/Port To capture protocol traffic with Wireshark when connected via OsmoSTP use port. Handling of Abnormal Events Related to the BSSAP Header. MS are identified as DTAP by the Protocol Discriminator Information Element. BSSMAP-LE PERFORM LOCATION ABORT message. If the SMLC cannot proceed with positioning due to some protocol violation or error condition (e.g.
|Published (Last):||3 June 2008|
|PDF File Size:||12.11 Mb|
|ePub File Size:||15.17 Mb|
|Price:||Free* [*Free Regsitration Required]|
The DTAP data is user information and carries messages related to call control and mobility management between two users, i.
UE User Equipment The phone or modem. The connection-oriented services are used for dedicated procedures such as handover and assignment procedures.
Global System for Mobile communication (GSM) protocol family
See SS7 for a description bsxmap SS7 protocols. The digital nature of GSM allows data, both synchronous and asynchronous data, to be transported as a bearer service to or from an ISDN terminal.
It authenticates the user in the network. The codes are shared by both the mobile station cellular phone and the base station, and are called pseudo-random code bssmqp.
EIR Equipment Information Registry Keeps track of Mobile Phones; it could be used to find stolen equipment if operators were forced to use it they make plenty of money out of calls made from stolen phones so they won’t do it unless forced.
Global System for Mobile communication GSM protocol family GSM is a technology bsamap digital wireless telecommunications, represented by a decent number of specifications. Figure shows the protocol stack used on these interfaces.
GSM A interface – BSS Application Part
One or more Kbps timeslots are used to carry signaling information. The radio link imposed some limitations, however, since the standard ISDN bit rate of 64 Kbps could not be practically achieved. It employs a commercial adaptation of a military spread-spectrum technology.
Direct transfer application part. Since each user is separated by a unique code, all users can share the same frequency band range of radio spectrum. CDMA is a spread spectrum technology, which means that it spreads the information contained in a particular signal of interest over a much greater bandwidth than the original signal.
CDMA has been used in many military applications, such as:. So two sets of protocols are used – Control Plane Protocols that control the calls and user plane protocols that carry the user’s data. See the License page for details. BSS management application part. At the physical layer, it uses a 2-Mbps PCM30 link. The acronym was preserved but protoocol new, English meaning was given to it later, once the potential of the technology was understood.
MS Mobile Set The phone or modem. The primary difference is that access to the local exchange carrier LEC is provided bbssmap a wireless phone.
The HLR contains such data as the current roaming, redirection, and special services settings. Control Protocols IP Q.
Based on spread spectrum theory, it gives essentially the same services and qualities prtoocol wireline service. These messages are partially processed by the BSC to add necessary information required for other entities to process these requests. Protocols The GSM protocol family consists of many protocols, and other protocols are conveyed on top of these.
For more protocols related to cellular protocols see the following families: The most basic teleservice supported by GSM is telephony.
Protocol: GSM A interface – BSS Application Part
GSM, however, refers to more than just the “air interface”; it refers to the complete set of protocols. The GSM recommendations do not encourage the use of this interface and have not updated specifications for this interface since Release Table lists local operation codes and their functions.
The B interface is an internal interface and is not visible in most implementations.
This message is sent to in response of protcool message which can not be treated correctly by the receiving entity and for which another failure message can not substitute. A slave of the BSC from which it takes its configuration.
Figure shows this interface and protocol stack. This message is sent protovol an entity to its peer entity that it is using one or more circuit identity code which are unknown.
ISUP is used for both speech and data call setup. Request to start a trace of a single connection. By the beginning ofthere were 1.