ASTM A – Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar. This standard is a part of ASTM. ASTM A March 10, Standard Specification for Annealed or Cold- Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar. This specification. ASTM A – Designation: A – 10 Standard Speci?cation for Annealed or Cold-Worked Austenitic.
|Published (Last):||1 April 2016|
|PDF File Size:||5.55 Mb|
|ePub File Size:||9.11 Mb|
|Price:||Free* [*Free Regsitration Required]|
Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. Maximum unless otherwise indicated. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. Current edition approved Sept. HRC typical L Ann 25 min. A number in parentheses indicates the year of last reapproval. The choice of test method for materials in conditions other than annealed shall be at the option of the seller.
If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. However, z666-10 the case of dispute, tests shall be made by pressure. In case of dispute, the offset method of determining yield strength shall be used.
Type L Stainless Steel is preferred in welding applications to exclude the formation of chromium carbides during cooling in the heat affected region of the weld. The values obtained in this manner should not, however, be taken as the actual yield strength for 0.
Your comments are invited either for revision of this standard or for additional standards and should be addressed to Asrm International Headquarters. Type L should be used in heavier sections to reduce the occurrence of carbide precipitation in the heat affected region adjacent to the weld pool. Types and L provides corrosion resistance in a wide range of moderately oxidizing and reducing conditions, fresh water and non-marine applications. Individual reprints single or multiple copies of this standard may a666–10 obtained by contacting ASTM at the above address or at phonefaxor service astm.
Only annealed conditions of grades speci? A66-10 L LN These alloys represent an excellent combination of corrosion resistance and fabricability. The values given in parentheses are for information only. Find out what NKS can do for you. C Annealed material that naturally meets mechanical properties may be applied.
S666-10 equipment and piping, heat exchanger components, dairy and food handling equipment and utensils, cryogenic vessels and components, architectural and structural applications exposed to non-marine atmospheres. Due to the high work hardening rate of these materials, intermediate anneals maybe required to successfully fabricate the part.
ASTM A for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar
Chemical equipment and piping, heat exchanger components, dairy and food handling equipment and utensils, cryogenic vessels and components, architectural and structural applications exposed to non-marine atmospheres Chemical Composition: Depending on the work hardening characteristics of the particular grade, either the yield or the tensile strength can be the controlling factor in meeting the properties. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every?
HardC Elongation in 2 in. D PSS means plate, strip, sheet. Heat to o F to o F and cool at sufficiently high rates through oF to oF to avoid precipitation of chromium carbides. Permission rights to photocopy the standard may also be secured from the ASTM website www. In the annealed condition it is essentially non-magnetic and becomes slightly magnetic with the application of cold work.
If filler metal is required, Type is normally used. A — 10 Standard Speci? B Type is generally produced with a chemical composition balanced for rich side Type or lean side Type austenite stability depending on the properties required for speci?
This revision of Speci?
This standard has been approved for use by agencies of the Department of Defense. Hard Elongation in 2 in.
304 and 304L Stainless Steel
Specimens shall be bent around a diameter equal to the product of the bend factor times the speci? Material Test Report and Certi? Originally approved in Rockwell B 95 95 Annealed Types and L can be fabricated by roll forming, deep drawing, bending and most other fabrication techniques.
The noncontrolling factor normally will a6666-10 considerably the speci? Types and L are weldable by most fusion or resistance welding techniques. Types and L cannot be hardened by thermal treatment.